If you have recently installed a new stereo or removed the seats in your Nissan, you may have noticed the airbag status light will not stop blinking. There is a simple fix for this that will keep you from having to take it to the dealer. Follow these steps to reset the airbag status light on a Nissan Auto.

Notice that the light will stay on and then start blinking. After turning the key to ON, wait until the light turns to off, to start the blinking process, and then switch the key OFF and remove the key.

nissan frontier abs light reset

Wait 5 seconds and repeat step 1. This should be completed three times. The status light may have a different blinking pattern at this point. Simply follow the same simple steps. Insert the key into the ignition and turn it to ON. Wait until the light turns off to start the blinking process and quickly turn the key to OFF and remove the key.

nissan frontier abs light reset

Do this process a total of 2 more times. When you are complete, you should have inserted the key and removed it for a total of 6 times. Now turn the key and start the car. The status light should stay lit and finally turn off as it normally should.

How to Reset The Airbag Status Light On A Nissan

If the light begins to blink again, repeat the steps above. This article was written by the It Still Runs team, copy edited and fact checked through a multi-point auditing system, in efforts to ensure our readers only receive the best information. To submit your questions or ideas, or to simply learn more about It Still Runs, contact us. Step 1 Insert the key into the ignition and turn the key to ON.

Step 2 Notice that the light will stay on and then start blinking. Step 3 Wait 5 seconds. Stick the key back in the ignition and repeat step 1.Nissan Frontier owners have reported 6 problems related to brake abs warning light under the service brakes category. The most recently reported issues are listed below.

Also please check out the statistics and reliability analysis of Nissan Frontier based on all problems reported for the Frontier. At ambient temperatures less than 10 degrees, the abs light and traction control light will illuminate upon first movement.

This disables the abs system and the traction control system, it will also disable the 4 wheel drive system if not engaged before movement. Ambient temp must rise above 25 degrees to reverse the symptoms. This is a serious safety hazard for anyone that lives in a cold climate. See all problems of the Nissan Frontier.

The contact owns a Nissan Frontier. While driving 40 mph, the vehicle failed to completely stop when the brakes were applied.

The contact could not estimate the length of time the vehicle took to stop. He stated that the abs warning indicator light illuminated. The road conditions were dry. The current and failure mileages wereThe contact stated that the abs fails intermittently. When the sensor activates, she hears a noise coming from the engine compartment and the brakes fail to work properly.

The failure has almost caused her to rear end another vehicle twice, while driving 20 mph. The repair shop stated that they were unable to locate a new sensor to replace the defected one. The current mileage wasand failure mileage wasAbs light intermittently lights on dashboard, causing per owners manual inoperative state of abs system.

How to Reset The Airbag Status Light On A Nissan

Light comes on when starting, while driving or sitting and idling. While traveling on the highway without prior warning. The abs braking light will appear on the dashboard. And will stay on until the vehicle is turn off. Please provide additional information dealer is aware of the problem. Car Problems. Service Brakes problems. Brake Electric Antilock problems.

Brake Master Cylinder problems. Brake Disc Caliper problems. Brake Foundation Components problems. Brake Pedal And Linkage problems. Brake Disc Pads problems. Brakes Failed problems. Brake Disc problems.I have a Nissan Frontier. Sometimes on the highway, sometimes acceleating, sometimes braking, sometimes a bump in the road, sometimes at startup. Once on, they do not go off until the engine is shut off. Operation of the vehicle, acceleration and braking, with the lights on, seems normal.

Items that may or may not be relevant, this started just after the transmission was changed. And continues after tires were replaced.

My mechanic says there is one sensor associated with the ABS on this vehicle. Is this an indication of something I should be concerned about?

This is telling you there is an issue with the braking system that could be dangerous. The ABS light going on could be in response to the brake light, and could be shutting off the ABS system to prevent brake system damage.

There are at least 4, one on each wheel. There is also a brake fluid pump and accumulator that have pressure sensors. Repairing these systems can get very expensive. What should I look for in the owner manual? What should I look for?

As to the flip remark to remove it, well, I thought it was there for a reason and thought someone on this forum would know something relevant. Maybe someone besides you.

On my vehicle, the brake warning light is triggered by the level of fluid in the master cylinder, indicating a hydraulic leak or worn pads, or by the parking brake handle being pulled. It does not initiate the ABS warning light. The brake warning light going on because the parking brake is engaged or the fluid level low will not turn on the ABS light. There are other sensors in the brake system that WILL turn on both lights. Some brake systems have a sensor on the master cylinder that will get triggered if there is a problem with the pressure differential between the two brake circuits.

nissan frontier abs light reset

This problem should trigger the ABS light with the brake light. Mountainbike, I have a Camry and the brake light system is exactly as you describe. I checked this out in the factory manual wiring diagram.

nissan frontier abs light reset

The brake light is only illuminated by the brake handle or the fluid is low in the reservoir. I was surprised at this since previous cars I had used a pressure differential switch to turn on the light. BustedKnuckles July 5,pm 2. Have you checked your brake fluid level? Caddyman July 5,pm 5.

How to Reset the Air Bag Warning Light on a Nissan EASY! No tools required!!

Tester July 5,pm 8.The ABS light on a Vehicles is designed to alert the driver to potential problems with any part of the anti-lock braking system. The ABS computer continuously monitors a number of sensors throughout the Vehicles in order to ensure that the anti-lock braking system is functioning properly Vehicles all times. When the ABS computer detects a problem with the system, it stores a trouble code in its internal memory and turns on the ABS light. Take the vehicle to a mechanic and have the anti-lock brake system checked and any necessary repairs made.

Usually this will turn off the ABS light, but not always. If not, proceed to Step 2. Put the key into the ignition and turn it to the "Run" position the position right before the one used to engage the engine. Locate the DIC control panel on the dashboard in front of the driver's seat under the speedometer. Open your Explorer's hood and loosen the retaining nut on the negative battery cable clamp using a socket wrench and a 10 millimeter socket. Check the dash to verify that the ABS light has gone out.

This process also resets all trouble codes in the Explorer's computer, so all other warning lights will reset as well. Put the key into the ignition and turn it to the second position. This is the position just before the engine starts. Open the hood of the Ford and loosen the nut on the negative battery cable clamp.

You can do this with a 10mm wrench. Put the clamp back in place and tighten the nut. Look on the dashboard to make sure the ABS light has turned off. This resets all lights in the car and the clock as well.

How to Reset the ABS Light on Vehicles

Drive the vehicle onto a flat surface and shift the transmission into "Park" or first gear manual transmission. Turn off the engine and apply the parking brake. This port is located underneath the dashboard, just above the pedal area. It is approximately 2 inches wide, a half-inch tall and made from black plastic. Wait a moment while the scan tool clears the trouble codes.

Turn off the scan tool, unplug it from the vehicle and start the engine. Confirm that the ABS light is no longer on. Items you will need Socket wrench Socket set. Items you will need 10mm open-end wrench Ignition key. Items you will need Automotive scan tool.Nissan Frontier owners have reported 55 problems related to air bag light on under the air bag category. The most recently reported issues are listed below. Also please check out the statistics and reliability analysis of Nissan Frontier based on all problems reported for the Frontier.

I have trouble shot the airbag light I have that has been blinking for a week now. I can not figure it out. I have noticed many posts on forums about this issue. I do not have a recall. The second issue is the truck idles rough, I have also seen many forums about this issue as well.

See all problems of the Nissan Frontier. Remains on whether standing still or in motion at any speed. Front air bag sensor not operating. Air bag light flashes. I have repeatedly gotten indicators via vehicle's computer of air bag failure, on a vehicle of low mileage, which has never been in an accident, and has gotten failures regarding the front passenger seat, which is rarely used.

The first time, the dealer replaced the seatback and airbag under warranty. The second time the dealer replaced the seatbelt assembly. Each time I get this failure notification, my airbag is disabled. So, it is an ongoing issue. The air bag failure light keeps coming on randomly, not related to a driving incident. Tl the contact owns a Nissan Frontier. Upon starting the vehicle, the air bag warning indicator illuminated. The contact took the vehicle to dorschel Nissan w henrietta rd, rochester, NYand was informed that the vehicle was not included in a recall; therefore, he would have to pay for the diagnostic testing and repair.The abs and traction control light came.

The 4x4 blinks. I have cleaned the abs sensors. Changed front breaks and rotors. Checked wiring and fluid levels. Lights still on and no 4x4. Has anyone found a solution for this?

GuruBF1FB answered about a year ago. I have the same problem right now with my wire was broken half and rewired back together work for a while now I'm have to order a new sensor and I'll see if that works. Checked wiring and Where can i find an owners manual for Nissan Frontier 4x4 V6 super charger.

Content submitted by Users is not endorsed by CarGurus, does not express the opinions of CarGurus, and should not be considered reviewed, screened, or approved by CarGurus. Please refer to CarGurus Terms of Use. Content will be removed if CarGurus becomes aware that it violates our policies. Report Follow. Mark helpful. Your Answer:. Upload Photo Photo optional. Related Questions.

Start a new Nissan Frontier question. Search Nissan Frontier Questions. Nissan Frontier Experts. Find great deals from top-rated dealers TM Search. Related Models For Sale.Have you got an ABS warning light on? Anytime a problem occurs in the ABS brake system the warning light gets on. In fact, ABS light stays on unless you fix the core issue. Basically, the warning light alerts the driver that the safety system is no longer active.

Anti-lock brake system ABS is very familiar to modern cars. This system has the functions of maintaining control and directional stability of a car when extreme braking happens.

When one or more tires start to skid, they will lose traction allowing the vehicle to move in whatever direction it wants, even totally sideways. Research has proven that a vehicle with an ABS system can decrease the risk of a vehicle accident by 18 percent by controlling the rotational speed of each wheel.

Located near the wheel, a wheel speed sensor is used to control the rotational speed of the wheel. This information is sent to the computer module, which measures all of the data from 4 wheel sensors. If the computer detects one or more wheels turning slower than the others, it will alert the valve to reduce the pressure of the brake line and then have the pump maintain this pressure to enable the wheel to start rolling again.

This is why you might feel the brake pedal vibrate if the system is activated. If the ABS system detects a problem, a fault code will be generated and then stores in the system memory to turn the warning light. Although early models included many parts, most of the modern systems are basic and consisted of 4 wheel speed sensors, main computer module, a valve and hydraulic pump assembly at every wheel. This helps to make the price of the parts more affordable as well as simplify repairs.

To begin with how to fix ABS lightpark your car over a stage with the engine off and setting the transmission and the emergency brake. It is protected by a fuse that may blow with time.

2012 Nissan frontier abs and traction control light on. 4x4 blinks

At first, replace the faulty fuse. In case it blows repeatedly, we can conclude that there is a problem in the pump motor or ABS computer. The ABS wheel sensor monitors the wheel rotation, controlled by its computer. This sensor works as a conjunction with the wheel stator attached to axle brake rotor, bearing hub or CV joint. With time, these sensors may short out as they are subject to vibration or road conditions. The ABS controller works in monitoring the wheel speed and may stop functioning like any other electronic device.

You can see the computer on the top of the pump motor, attached to around five mounting bolts. The wheel speed sensor and the other sensor work in combination to monitor the rotation speed of the wheel. A damaged wheel ring causes trouble to the whole system. In any case, the ring damages or dislocates in a way that the teeth remain absent, this, activates the system. Further, the system stays activated assuming the wheel is rotating slower than all others.

One of the causes responsible for ABS light stays on is losing hydraulic pressure. When inspecting why your ABS warning light stays onyou need to inspect the levels in your brake reservoir to see whether it has lost a significant amount of brake fluid or not.

Low levels of the brake fluid is a possible cause making the warning light stays on. On the other hand, if the levels are not perfect, it might be that you are losing pressure on one side of the vehicle, which can be very dangerous.

Therefore, you should try to find out how to reset ABS brake system. Each vehicle has 2 hydraulic circuits and you need to inspect both of them as well. In the situation when the main line fails, the dual hydraulic system works as a fail safe, so there is still the opportunity that the second set of brakes will kick in and enable the car to stop. These are built into a check valve system that enables one to turn when the other turns off.

So if you detect damaged parts in the hydraulic circuits, you can replace them, but if the ABS light stays onyou may have a more dangerous issue in the actual brake lines. Another reason causing ABS light stays on is the emergency brake.